l features l outline ? 2-color type led ? abundant 2 color variations l size 1006 (0402) 1.00.6mm (t=0.2mm) l dimensions l specifications typ. i f max. v r min.* 3 typ. max.* 3 i f min. typ. i f (v) (ma) ( m a) (v) (nm) (nm) (nm) (ma) (mcd) (mcd) (ma) 2.9 465 470 475 9 22 1.9 619 624 629 10 21 2.1 569 572 575 14 40 1.9 615 620 625 22 63 569 572 575 16 40 615 620 625 25 63 2.2 569 572 575 5.6 16 1.9 615 620 625 22 63 569 572 575 10 25 602 605 608 40 100 2.2 569 572 575 5.6 16 1.9 602 605 608 22 63 2.2 569 572 575 5.6 16 1.9 584 587 590 22 63 * 1:duty1/5, 1ms * 2:duty1/10, 1khz * 3:reference topr(oc) tstg(oc) 5 4 2.2 color i fp (ma) current v r (v) voltage dissipation current p d (mw) i f (ma) 60* 1 yellowish green orange yellowish green yellow 54 yellowish green blue red red yellowish green 66 50 52 50 54 70 red green sml-52 series ingan aigainp sml522bu1w sml-522muw sml-522mu8w sml-521muw SML-522MD8W red green 50 orange 60* 2 60* 1 100* 2 part no. chip structure absolute maximum ratings (ta=25oc) emitting power forward peak forward reverse operating temp. sml-521mdw sml-521myw aigainp gap aigainp aigainp gap aigainp gap aigainp 100* 2 60* 1 70 50 70 50 20 20 25 20 20 25 20 25 20 5 4 - 40 to + 85 - 30 to + 85 - 40 to + 85 - 30 to + 85 - 40 to + 85 - 30 to + 85 - 40 to + 85 2.2 5 20 - 40 to + 100 - 40 to + 85 - 40 to + 100 - 40 to + 85 - 40 to + 100 l recommended solder l pattern 5 20 5 20 10 100 5 4 electrical and optical characteristics (ta=25oc) storage temp. forward voltag v f reverse current i r dominant wavelength l d luminous intensity i v (unit : mm) (note ) tolerance is ? 0. 1 mm, unless otherwise specified. (unit : mm) 1315 (0605) 1.3 1.5mm (t=0.6mm) color type u b u m d m y m sml - 521 series / sml - 522muw sml - 522 * 8w series / sml522buw 1/9 2013.09 - rev.d datasheet www.rohm.com ? 2013 rohm co., ltd. all rights reserved.
sml-52 series l electrical characteristics curves 1 10 100 1.4 1.8 2.2 2.6 3.0 3.4 0.2 0.6 1 1.4 1.8 -40 -20 0 20 40 60 80 100 0.0 1.0 2.0 3.0 4.0 0 4 8 12 16 20 0 10 20 30 -40 -20 0 20 40 60 80 100 fig.1 forward current - forward voltage s forward current : i f [ma] forward voltage : v f [v] fig.2 luminous intensity - atmosphere temperature relative luminous intensity [a.u.] atmosphere temperature : ta [oc] fig.3 luminous intensity - forward current relative luminous intensity [a.u.] forward current : i f [ma] fig.4 derating maximum forward current : [ma] ambient temperature : ta [oc] ta=25 oc ta=25 oc i f = 5ma sml522bu1w (u) sml522bu1w (b) sml522bu1w (u) sml522bu1w (b) sml522bu1w (u) sml522bu1w (b) sml522bu1w (u) sml522bu1w (b) (note) in case of lighting a single color. * the value is based on the die destruction endurance; optical characteristics are not considered.. 2/9 2013.09 - rev.d www.rohm.com ? 2013 rohm co., ltd. all rights reserved. data sheet
sml-52 series l electrical characteristics curves 1 10 100 1.4 1.6 1.8 2.0 2.2 2.4 0.4 0.6 0.8 1 1.2 1.4 1.6 -40 -20 0 20 40 60 80 100 0.0 0.2 0.4 0.6 0.8 1.0 1.2 0 4 8 12 16 20 0 10 20 30 -40 -20 0 20 40 60 80 100 fig.1 forward current - forward voltage s forward current : i f [ma] forward voltage : v f [v] fig.2 luminous intensity - atmosphere temperature relative luminous intensity [a.u.] atmosphere temperature : ta [oc] fig.3 luminous intensity - forward current relative luminous intensity [a.u.] forward current : i f [ma] fig.4 derating maximum forward current : [ma] ambient temperature : ta [oc] ta=25 oc ta=25 oc i f = 20ma sml - 522muw (u) sml - 522muw (m) sml - 522muw (u) sml - 522muw (m) sml - 522muw (u) sml - 522muw (m) sml - 522muw (u) sml - 522muw (m) 3/9 2013.09 - rev.d www.rohm.com ? 2013 rohm co., ltd. all rights reserved. data sheet
sml-52 series l electrical characteristics curves 1 10 100 1.6 1.8 2.0 2.2 2.4 2.6 0.4 0.6 0.8 1 1.2 1.4 1.6 -40 -20 0 20 40 60 80 100 0.0 0.2 0.4 0.6 0.8 1.0 1.2 0 4 8 12 16 20 0 10 20 30 -40 -20 0 20 40 60 80 100 fig.1 forward current - forward voltage s forward current : i f [ma] forward voltage : v f [v] fig.2 luminous intensity - atmosphere temperature relative luminous intensity [a.u.] atmosphere temperature : ta [oc] fig.3 luminous intensity - forward current relative luminous intensity [a.u.] forward current : i f [ma] fig.4 derating maximum forward current : [ma] ambient temperature : ta [oc] ta=25 oc ta=25 oc i f = 20ma sml - 522mu8w (u) sml - 522md8w (d) sml - 522mu8w (m) sml - 522md8w (m) sml - 522mu8w (u) sml - 522md8w (d) sml - 522mu8w (m) sml - 522md8w (m) sml - 522mu8w (u) sml - 522md8w (d) sml - 522mu8w (m) sml - 522md8w (m) sml - 522mu8w (u) sml - 522md8w (d) sml - 522mu8w (m) sml - 522md8w (m) 4/9 2013.09 - rev.d www.rohm.com ? 2013 rohm co., ltd. all rights reserved. data sheet
sml-52 series l electrical characteristics curves 1 10 100 1.4 1.6 1.8 2.0 2.2 2.4 2.6 0.4 0.6 0.8 1 1.2 1.4 1.6 -40 -20 0 20 40 60 80 100 0.0 0.4 0.8 1.2 1.6 0 5 10 15 20 25 0 10 20 30 -40 -20 0 20 40 60 80 100 fig.1 forward current - forward voltage s forward current : i f [ma] forward voltage : v f [v] fig.2 luminous intensity - atmosphere temperature relative luminous intensity [a.u.] atmosphere temperature : ta [oc] fig.3 luminous intensity - forward current relative luminous intensity [a.u.] forward current : i f [ma] fig.4 derating maximum forward current : [ma] ambient temperature : ta [oc] ta=25 oc ta=25 oc i f = 20ma sml - 521muw (u) sml - 521mdw (d) sml - 521myw (y) sml - 521muw (m) sml - 521mdw (m) sml - 521myw (m) sml - 521muw (u) sml - 521mdw (d) sml - 521myw (y) sml - 521muw (m) sml - 521mdw (m) sml - 521myw (m) sml - 521muw (u) sml - 521mdw (d) sml - 521myw (y) sml - 521muw (m) sml - 521mdw (m) sml - 521myw (m) sml - 521muw (u) sml - 521mdw (d) sml - 521myw (y) sml - 521muw (m) sml - 521mdw (m) sml - 521myw (m) 5/9 2013.09 - rev.d www.rohm.com ? 2013 rohm co., ltd. all rights reserved. data sheet
sml-52 series l viewing angle l rank reference of brightness * measurement tolerance 10% scanning angle (deg) relative intensity scanning angle (deg) relative intensity sml - 521 series sml - 521 series (u/d/y) sml - 521 series (m) scanning angle (deg) relative intensity scanning angle (deg) relative intensity sml522bu1w (u/b) sml - 522muw (u/m) sml522bu1w (u) sml - 522muw (u) sml522bu1w (b) sml - 522muw (m) scanning angle (deg) relative intensity scanning angle (deg) relative intensity sml - 522 x 8w sml - 522 x 28w (u/d) sml - 522x8w (m) scanning angle (deg) relative intensity 6/9 2013.09 - rev.d www.rohm.com ? 2013 rohm co., ltd. all rights reserved. data sheet (ta=25oc, i f 20ma) rank k l m n p q r s t u iv (mcd) 4.0 to 6.3 6.3 to 10 10 to 16 16 to 25 25 to 40 40 to 63 63 to 100 90 to 140 140 to 220 220 to 360 red u yellowish green m red u green m red u yellowish green m orange d green m orange d yellowish green m y ellow y yellowish green m (ta=25oc, i f 5ma) rank k l m n p q r s t u iv (mcd) 4.0 to 6.3 6.3 to 10 10 to 16 16 to 25 25 to 40 40 to 63 63 to 100 90 to 140 140 to 220 220 to 360 red u blue b sml-521my w * part no. sml522bu1w part no. sml-522muw * sml-522mu8w * sml-521muw * SML-522MD8W sml-521mdw *
sml-52 series l taping [t86] l part no. construction l packing specification rohm led products are being shipped with desiccant (silica gel) concluded in moisture-proof bags. pasting the moisture sensitive label on the outer surface of the moisture-proof bags or enclosing the humidity indication card inside the bag is available upon request. please contact the nearest sales office or distributer if necessary. 7/9 2013.09 - rev.d www.rohm.com ? 2013 rohm co., ltd. all rights reserved. data sheet 8 0.8 1.75 3.5 5.5 0 0.5 1.65 4 2 1.95 180 60 13 11.4 0.1 0.1 0.05 1 -3 0 +1 0 1.5 0.1 0 packing quantity 4000pcs/reel pull direction (note) tolerance is within 0.2mm unless otherwise specified unit : mm) +0.1 -0.07
sml-52 series l attention points in handling this product was developed as a surface mount led especially suitable for soldering. please take care of following points when using this device. 1.designing of pcb as for a recommendable solder pattern, please refer to fig-1. the size and direction of the pad pattern depend on the condition of the pcb. thorough design review is recommended before the final designing this product of structured with rear/bottom electrode to be soldered. the formation of solder fillet is not guaranteed due to its electrode shape. 2.soldering (sn-cu, sn-ag-cu, sn-ag-bi-cu) led products do not contain reinforcement materials such as glass fillers. therefore, thermal stress by soldering greatly influence its reliability. the temperature conditions for reflow soldering should therefore be set up according to the characteristic of this product. (see fig-2) number of reflow process shall be max 2 times and these processes shall be performed in a row. cooling process to normal temperature shall be required between first and second soldering process. 3.handling after mounting as shown right drawing, in case outside force of around 1kg is given to the device, stress is concentrated to the jointed part between mold resin and substrate. therefore there is a possibility to breat the device or pcb. careful handing is needed as rohm cannot guarantee the falling of the device by outside force after mounting. 4.washing please note the following points when washing is required after soldering. 4-1) washing solvent isopropyl alcohol or other alcohol solvent is recommendable. 4-2) temperature below 30oc, immersion time ; within 3 minutes. 4-3) ultra sonic washing below 15/1 litter of solvent tub. 4-4) cooling below 100oc within 3 minutes. 5.erosion gas utilization in erosion gas atmosphere may degenerate the plating surface which might cause deterioration of solder strength, optical characteristics, or functions. please take precautions against occurrence of gas from the surrounding parts on the occasion of custody, and also after mounted on circuit board. min.1 min max. 40sec max.2 5 0 oc, within 10sec 140 to 180 oc 23 0 to 2 6 0 oc (fig - 1) (fig - 2 ) 0.6mm 2.45mm 0.5mm 1.3mm outside force pcb mold substrate soldering part emitting direction 8/9 2013.09 - rev.d www.rohm.com ? 2013 rohm co., ltd. all rights reserved. data sheet
sml-52 series 6.storage at reflow soldering, the reliability of this product is often influenced by moisturet absorption so we apply the packaging with moisture proof for better condition is use, please also note that 6-1) not to be opened before using. 6-2) to be kept in our moisture proof packaging with some desiccant (silica gel) after opening it. to be baked in case the silica gel indicator changed its color from either blue to clear or green to pink. 6-3) please use within 168 hours after the package was opened. (condition at 30 o c, max.70%rh.) in case it is not used within 168 hours, please put it back into our packaging. 6-4) baking please bake under reel condition at 60 o c, 12 24 hours (max.20%rh) after un-sealing. while baking is done, the reel and emboss tape may be easily deformed. please be careful not to give any stress. 7.life time this product will cause reduction of luminous intensity depending on the using conditions and environmental. please inquire our sales contact if long life time is required on your application. 9/9 2013.09 - rev.d www.rohm.com ? 2013 rohm co., ltd. all rights reserved. data sheet
r1102 a www.rohm.com ? 2013 rohm co., ltd. all rights reserved. notice rohm customer support system http://www.rohm.com/contact/ thank you for your accessing to rohm product informations. more detail product informations and catalogs are available, please contact us. notes the information contained herein is subject to change without notice. before you use our products, please contact our sales representative and verify the latest specifica- tions : although rohm is continuously working to improve product reliability and quality, semicon- ductors can break down and malfunction due to various factors. therefore, in order to prevent personal injury or fire arising from failure, please take safety measures such as complying with the derating characteristics, implementing redundant and fire prevention designs, and utilizing backups and fail-safe procedures. rohm shall have no responsibility for any damages arising out of the use of our poducts beyond the rating specified by rohm. examples of application circuits, circuit constants and any other information contained herein are provided only to illustrate the standard usage and operations of the products. the peripheral conditions must be taken into account when designing circuits for mass production. the technical information specified herein is intended only to show the typical functions of and examples of application circuits for the products. rohm does not grant you, explicitly or implicitly, any license to use or exercise intellectual property or other rights held by rohm or any other parties. rohm shall have no responsibility whatsoever for any dispute arising out of the use of such technical information. the products are intended for use in general electronic equipment (i.e. av/oa devices, communi- cation, consumer systems, gaming/entertainment sets) as well as the applications indicated in this document. the products specified in this document are not designed to be radiation tolerant. for use of our products in applications requiring a high degree of reliability (as exemplified below), please contact and consult with a rohm representative : transportation equipment (i.e. cars, ships, trains), primary communication equipment, traffic lights, fire/crime prevention, safety equipment, medical systems, servers, solar cells, and power transmission systems. do not use our products in applications requiring extremely high reliability, such as aerospace equipment, nuclear power control systems, and submarine repeaters. rohm shall have no responsibility for any damages or injury arising from non-compliance with the recommended usage conditions and specifications contained herein. rohm has used reasonable care to ensur the accuracy of the information contained in this document. however, rohm does not warrants that such information is error-free, and rohm shall have no responsibility for any damages arising from any inaccuracy or misprint of such information. please use the products in accordance with any applicable environmental laws and regulations, such as the rohs directive. for more details, including rohs compatibility, please contact a rohm sales office. rohm shall have no responsibility for any damages or losses resulting non-compliance with any applicable laws or regulations. when providing our products and technologies contained in this document to other countries, you must abide by the procedures and provisions stipulated in all applicable export laws and regulations, including without limitation the us export administration regulations and the foreign exchange and foreign trade act. this document, in part or in whole, may not be reprinted or reproduced without prior consent of rohm. 1) 2) 3) 4) 5) 6) 7) 8) 9) 10) 11) 12) 13) 14)
|
